A line output converter (LOC) is a device that converts a speaker-level audio signal to a line-level signal. This is typically used to connect a factory car stereo to an aftermarket amplifier. The LOC will have two sets of inputs and outputs. The input will be connected to the speakers of the factory car stereo and the output will be connected to the line-level input of the aftermarket amplifier.
6 Steps to Connect Line Output Converter
O.C. and how to use it. An LOC is used to connect an amplifier to a factory radio or to other source units when the source unit doesn’t have low-level output jacks. It converts the high-level signal from the source unit to a low-level signal that is compatible with the amplifier. The LOC will also provide impedance matching, so that the amplifier sees the correct load.
One of the most important skills that you can learn is how to connect a line output converter. This device is used to convert the electrical signals from your stereo’s preamp outputs into a stronger signal that can be sent to your amplifier. This is important because it allows you to get the most from your stereo system by sending a stronger signal to your amplifier.
Step 1: To Connect A Lineoutput Converter To A Stereo
To connect a line output converter, first remove the stereo’s factory head unit. Next, use a wiring harness to connect the line output converter to the head unit’s wiring. Once the wiring is connected, screw the line output converter into place and reconnect the stereo’s head unit.
Step 2: To Get Better Sound Quality From Your Music
There are a few things you can do to get better sound quality from your music. One is to connect a line output converter (LOC) between your music player and your car stereo. This will allow you to control the volume of your music without affecting the overall volume of your car stereo. It will also give you better sound quality by allowing you to keep your music player at a lower volume.
Step 3: To Connect An Amplifier To A Set Of Speakers
Installing a line output converter (LOC) is one of the easiest ways to add an amplifier to a factory stereo. An LOC will convert the speaker-level output of your factory stereo into a signal that can be understood by your aftermarket amplifier. This guide will show you how to install a line output converter in your vehicle.
Step 4: To Boost The Signal From A Device Like An Ipod
To connect a line output converter, first disconnect the negative battery terminal to avoid any sparks. Next, connect the audio input of the converter to the head unit’s audio output or the amplifier’s pre-out. Then, use RCA cables to connect the converter’s audio output to the head unit’s audio input or the amplifier’s input. Finally, reconnect the negative battery terminal and test the system to make sure it is working properly.
Step 5: To Power Up A Set Of Speakers
To connect a line output converter, you’ll need to first connect the line output converter to the speaker wire. Next, connect the other end of the line output converter to the stereo receiver. Finally, turn on the receiver and enjoy your music.
Step 6: To Add A Subwoofer To Your Music System
If you want to add a subwoofer to your music system, you’ll need to connect a line output converter. This will allow you to connect the subwoofer to your music system.
Frequently Asked Questions
Where Does A Line Output Converter Go?
A line output converter (LOC) is an audio device that converts a digital input signal into an analog output signal. It is typically used to connect a computer or other digital audio source to a stereo system or power amplifier. The LOC is usually connected to the “line in” or “auxiliary” input of the stereo system.
What Does A Line Output Converter Do?
A line output converter is a device that is used to convert the signal from a stereo audio source to mono. This is useful when you only have one speaker and want to play the audio from both the left and right channels.
Does A Line Out Converter Need Power?
It depends on the converter. Some converters do not require power, while others require an external power supply.
In Summary
A line output converter is an essential piece of equipment for any car audio system. It allows the user to connect an amplifier to the factory radio without having to cut any of the factory wiring. By using a line output converter, the user can keep the OEM radio in place and still enjoy the benefits of an aftermarket amplifier.
