Skip to content

How To Hardwire A Dashcam

A dash cam is a great way to have a continuous video record of your driving, and can be especially useful if you’re ever in an accident. While you can buy a dash cam that plugs into your cigarette lighter, it’s better to hardwire it into your car’s electrical system. Hardwiring a dash cam is not difficult, and only takes a few minutes.

7 Steps to Hardwire A Dashcam

One way to hardwire a dashcam is to connect it directly to the battery. This will ensure that the dashcam will always have power and will never miss a recording. Another way to hardwire a dashcam is to connect it to the fuse box. This will allow the dashcam to tap into the power of the car’s electrical system and will never run out of power.

In an increasingly technology-driven world, it is important to know how to hardwire a dashcam. This process allows you to avoid potential problems with battery life and recording capacity. Additionally, hardwiring your dashcam can give you a clearer picture quality than if it were relying on a battery.

Step 1: How To Hardwire A Dashcam

1. Park your vehicle in a safe location and turn off the engine. 2. Find an unused fuse in your vehicle’s fuse box. Use a fuse tap to connect the dashcam’s power wire to the fuse. 3. Route the power wire behind the dash and to the front of the vehicle. 4. Plug the power wire into the dashcam. 5. Test the dashcam to ensure it is receiving power.

Step 2: Find A Power Source For Your Dashcam

If your dashcam doesn’t have a built-in battery, you’ll need to find a power source for it. The best option is to hardwire it into your car’s electrical system. This can be done by running a wire from the dashcam to the fuse box or directly to the battery. If you’re not comfortable doing this yourself, you can take it to a professional car stereo installer.

Step 3: Identify Where To Tap Into Your Car’S Fuse Box Purchase An Appropriate Fuse Tap

To hardwire a dashcam, first identify where to tap into your car’s fuse box. Then purchase an appropriate fuse tap. Use the tap to connect the positive wire from the dashcam to the fuse box. Finally, use the tap to connect the negative wire from the dashcam to a ground point.

Step 4: Cut The Power Cord Of Your Dashcam To The Desired Length

Cut the power cord of your dashcam to the desired length. If you are using a cigarette lighter adapter, make sure to also cut the adapter off so that only the cord is left. Next, strip the end of the cord so that the two wires are exposed. Finally, twist each wire around a connector and screw the connector tight.

Step 5: Strip The Insulation From The Power Cord And Attach The Appropriate Fuse Tap

Use a fuse tap to hardwire your Dashcam to your car’s fuse box. This will provide a constant power source for your Dashcam, even if your car’s battery is disconnected or drained. To do this, first strip the insulation from the power cord and attach the appropriate fuse tap to the exposed wire. Then, use the included wire strippers to strip away a small section of the wire coating on the end of the fuse tap. Finally, twist the exposed

Step 6: Connect The Power Cord Of Your Dashcam To The Fuse Tap

To hardwire a dashcam, you will need to connect the power cord of your dashcam to the fuse tap. The fuse tap will need to be connected to a constant power source, typically found in the fuse box.

Step 7: Close Up The Fuse Box

To hardwire a dashcam, you will need to close up the fuse box. This will protect the dashcam from any electrical surges.

Frequently Asked Questions

How Do I Wire My Dash Cam Directly To My Car?

If you want to wire your dash cam directly to your car, you’ll need to find a power source in your car that is always on, such as the cigarette lighter. You’ll then need to find a way to tap into that power source and run the wire to your dash cam.

Is It Good To Hard Wire Dash Cam?

There is no one definitive answer to this question. Some people believe that it is better to hardwire a dash cam in order to ensure that it is always powered on and recording footage, while others believe that this is not necessary and that a battery-operated dash cam will suffice. Ultimately, the decision about whether or not to hardwire a dash cam depends on the individual’s preferences and needs.

What Fuse Is Best To Hardwire A Dashcam To?

Most people recommend using a fuse rated for 10 or 15 amps when hardwiring a dashcam.

Summing-Up

Dashcams can be hardwired to your car’s electrical system in order to power on automatically and start recording video footage when the car is turned on. This can be done by tapping into the car’s fuse box and using a wiring harness to connect the camera to the power supply.

Leave a Reply

Your email address will not be published. Required fields are marked *